---
title: "Disk Array Issue: Rebuild HP server's RAID configuration"
canonical_url: "https://apidocs.sportradar.com/resources/avp/docs/troubleshooting/rebuild-raid"
markdown_url: "https://apidocs.sportradar.com/resources/avp/docs/troubleshooting/rebuild-raid.md"
last_updated: "2026-11-13T13:16:50Z"
---

# Disk Array Issue: Rebuild HP server's RAID configuration

This article will show you how to build the RAID configuration on an HPE Proliant server using HPE Smart Storage Administrator. Other servers might have a slightly different process.

This will be a necessary process when the server can not boot anymore and the message below is displayed:

![PXE boot error no logical drives](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/01-pxe-boot-no-logical-drives.webp)

![Start PXE over IPv4 message](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/02-start-pxe-over-ipv4.png)

## Preparation

Make sure you have the following items below:

- VGA monitor
- Mouse
- Keyboard

Plug the monitor into the server's VGA connector (the blue connector). It is located in the back of the server.

Plug the mouse and keyboard into any free USB port the server has.

## Reboot or Power on the Server

Reboot or power on the server from the server's front panel.

## Launch Intelligent Provisioning

One of the fastest ways to get to HPE SSA (Smart Storage Administrator) is through the HPE Intelligent Provisioning menu. During system POST phase press **F10** to launch Intelligent Provisioning.

![POST screen press F10 prompt](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/03-post-press-f10-intelligent-provisioning.png)

## Access the HPE Smart Storage Administrator

In the HPE Intelligent Provisioning menu select the option titled **HPE Smart Storage Administrator** – **you have only 15 seconds to achieve this**, so try to be as quick as possible, otherwise you will be redirected to the default option:

![Intelligent Provisioning HPE SSA menu](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/04-intelligent-provisioning-ssa-option.png)

The below picture presents the HPE Smart Storage Administrator GUI main screen:

![HPE Smart Storage Administrator main screen](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/05-hpe-ssa-main-screen.png)

> **Note**
>
> The example here uses a P440 controller. Other servers may be equipped with different controllers, i.e. B140. Since they are all managed by HPE SSA, the procedure of array configuration should be the same for each controller.

## Create RAID 1 Storage Array in HPE SSA

On the HPE SSA main screen click on the array controller.

![Array controller on SSA main screen](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/06-click-array-controller.png)

In the Smart Array **Actions** menu, choose the **Configure** option.

![Configure option in Actions menu](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/07-actions-menu-configure.png)

Click on the **Create Array** button.

![Create Array button in SSA](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/08-create-array-button.png)

The example below uses two hard drives but it's still the same process with a single one.

![Select physical drives for array](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/09-select-physical-drives.png)

In the **RAID level** section, ensure that **RAID 1** *(or RAID 0 if it is the only available option)* has been chosen. You can leave the remaining parameters at their default values. Click on the **Create Logical Drive** button to create RAID 1 array.

![RAID 1 level and Create Logical Drive](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/10-raid1-create-logical-drive.png)

Look over the summary screen to verify the newly created array and click on the **Finish** button.

![Array summary Finish confirmation](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/11-array-summary-finish.png)

The new array should now appear in the left pane of the main HPE SSA window.

![New array in SSA left pane](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/12-new-array-left-pane.png)

## Exit the HPE Smart Storage Administrator

Click on the **X** button to exit the application and then you will be redirected to Intelligent Provisioning screen. On the Intelligent Provisioning screen click on the **Power Button** in the upper right corner to reboot the server. If you do not see this button, you can reboot the server by powering it down and back up again using the button on the server's front panel.

![Exit SSA and reboot power button](https://apidocs.sportradar.com/resources/avp/static/troubleshooting/_assets/rebuild-raid/13-exit-ssa-reboot-power.png)

> **Info**
>
> Need help? Contact us at <avpo-support@sportradar.com>.
